wire rate

Even the relative low wire feed rate of 6 m/ min exceeds 3 times of routine TIG welding, which greatly improves the welding efficiency.

6~10m/min的送丝速度较常规TIG焊接提高了3倍以上，大大提高了焊接效率。

互联网摘选

A laser overlaying experiment was studied on 45 steel matrix with special alloy wire by using different laser power, scanning velocity and wire feed rate.

在45钢基体上，选用不同的激光功率、扫描速度、送丝速度，用专用焊丝进行堆焊试验。

互联网摘选

In 108 cases using the special preshaped guide wire, the success rate of catheterization was 100%.

对108例患者利用特制钩形角部定位导丝行介入再通，插管成功率为100%。

互联网摘选

In the three conditions, wire feed rate variety are within 10%, and accord with the JB/ T8748 1998, MIG/ MAG arc welding machine standard demands.

送丝速度变化率在三种情况下均小于10%，符合JB/T8748-1998，MIG/MAG弧焊机标准要求。

互联网摘选

In this paper, the following is introduced, the setting for laser welding with filler wire, the interaction between laser beam and filler metal and weldment, the relations between wire feed rate and welding speed.

介绍了激光填丝焊的装置；论述了光束与焊丝和工件的相互作用及送丝速度与焊接速度之间的关系；

互联网摘选

The effects of process parameters such as laser power, welding speed, wire feed rate, defocusing distance, laser-wire distance, filler wire angle, shielding gas are studied in detail.

研究了工艺参数对焊缝成形质量的影响，如激光功率、焊接速度、送丝速度、离焦量、光丝间距、送丝角度、送丝方式以及保护气体等，并获得了优化的工艺参数。

互联网摘选

The droplet transfer cycles were controlled by wave control method. Also gradual adjustment of the sequential and wire feed rate was controlled by software.

采用波形控制方法对熔滴过渡周期进行控制，同时软件还对时序系统和送丝速度进行精密渐变控制。

互联网摘选

The model of optimum feeding Al wire rate in LF refining was developed. The available feeding Al wire rate was calculated with the condition of different temperature and weight of liquid steel for a 60 ton LF at Daye Special Steel Co Ltd.

建立了LF精炼过程喂Al线速度模型，分别计算了大冶特殊钢股份有限公司60t钢包炉生产过程中钢液不同温度、不同重量条件下的最佳喂入速度。

互联网摘选

The white fracture tendency of thin wall nodular iron casting still has relation with storing time of base molten iron, inoculation method, cored wire injection qualities, wire feeding rate and pouring time and so on.

薄壁球铁件白口倾向还与原铁水的静止时间、孕育、芯线加入量、喂线速度、浇注时间有关。

互联网摘选

The best wire feeding rate is 12m/ min.

最佳喂线速度为12m/min；

互联网摘选

It is also pointed out that the intrinsic self regulation effect of wire melting rate exists in case of electrical short circuit.

证实了阳极斑点爬升现象，测定了弧长恢复时间常数，并指出短路过渡时也存在着焊丝熔化率的自身调节作。

互联网摘选

Effects of different experimental parameters, such as diameters and material of discharge wire, total rate of H_2-O_2 feed, oxygen concentration on the generation of H_2O_2 have been systematically studied.

系统地考察了放电电极材质、放电电极直径、氢气和氧气进料总气速和氧气浓度等参数对H2O2生成的影响。

互联网摘选

But the drawing of the complicated section special shaped wire must consider processing rate and speed.

对复杂断面的异型材，在拉拔时要考虑道次加工率和拉拔速度。

互联网摘选

A Portable Instrument for Measuring Wire Feed Rate

便携式送丝速度测量仪

互联网摘选

Two groups of matching relation of the weld speed and the wire feed rate were found in a condition of invariable laser power and focus position.

前者试验获得了一定激光功率和离焦量条件下两组焊接速度和送丝速度的匹配关系，并发现填充焊丝的加入对焊缝咬边现象确有改善；

互联网摘选

The linear relationship between wire resistance rate and temperature is justified had on Newton's law of radiation.

结合牛顿散热定律，验证订丝电阻率与温度的线性关系。

互联网摘选

Because the wire can obtain energy from laser indirectly, the high quality welds and the stability of the welding process could be received by using the higher wire feeding rate.

由于激光对焊丝的热作用，激光-GMA复合焊可以在较高的送丝速度下得到良好的焊缝成形和稳定的焊接过程。

互联网摘选

Welding parameters such as angle of bending tip, pulse voltage, wire feed rate, pulse mode, size of groove and welding speed can affect the appearance of weld.

导电嘴弯曲角度、送丝速度、峰值电压、协同模式、焊接速度和坡口尺寸均会对窄间隙焊缝成形产生重要影响。

互联网摘选

But at any rate they could plug in your wire whenever they wanted to.

起码只要愿意,他们总可以接通你的线路呀.

英汉文学

Application of diagnostic technique such as myocardial contrast echocardiography and Doppler wire improved detection rate of no-reflow phenomenon.

心肌对比超声及多普勒导丝等诊断技术的应用提高了无复流的检出率。

互联网摘选